RELEASE NOTES FreeBSD Release 3.2-RELEASE Welcome to 3.2-RELEASE, a full follow-on to the 3.1-RELEASE released February 1999 and which marked the beginning of the 3.0-STABLE branch. In the 4 months since 3.1 was released, many hundreds of bug fixes and general enhancements were made to the system. Please see relevant details below. Any installation failures or crashes should be reported by using the send-pr command (those preferring a WEB based interface can also see http://www.freebsd.org/send-pr.html). For information about FreeBSD and the layout of the 3.2-RELEASE directory (especially if you're installing from floppies!), see ABOUT.TXT. For installation instructions, see the INSTALL.TXT and HARDWARE.TXT files. Table of contents: ------------------ 1. What's new since 3.1-RELEASE 1.1 KERNEL CHANGES 1.2 SECURITY FIXES 1.3 USERLAND CHANGES 2. Supported Configurations 2.1 Disk Controllers 2.2 Ethernet cards 2.3 ATM 2.4 Misc 3. Obtaining FreeBSD 3.1 FTP/Mail 3.2 CDROM 4. Upgrading from previous releases of FreeBSD 5. Reporting problems, making suggestions, submitting code 6. Acknowledgements 1. What's new since 3.1-RELEASE --------------------------------- 1.1. KERNEL CHANGES ------------------- Added driver support for PCI gigabit ethernet adapters based on the Alteon Networks Tigon 1 and Tigon 2 chipsets, including the Alteon AceNIC, 3Com 3c985 and Netgear GA620. Support for USB devices further improved. Support has been added for direct access to NTFS filesystems. Support has been added for Joliet extensions on ISO 9660 filesystems. Only iso8859-1 characters (latin-1) are supported at this time, though. Support has been added for Adaptec 2930U2 and 3950U2 SCSI cards. There have been a couple of kernel changes that will break the binary interface for clients of the CAM passthrough interface or the devstat(9) statistics interface. These changes were made to fix some interface deficiencies. We regret any inconvenience this will cause, but we anticipate that this will have minimal impact as there are no known commercial binary-only applications that use either interface. This will require that programs that use those two interfaces be recompiled. Ports that use the CAM interface include xmcd, tosha, SANE, cdrecord and cdda2wav. Ports that use the devstat interface include xsysinfo and xperfmon. 1.2. SECURITY FIXES ------------------- Descriptor leak bug which was potentially open to a denial of service attack (by local users) was closed. REF: KKIS.05051999.003b 1.3. USERLAND CHANGES --------------------- The Internet Software Consortium's DHCP client has been added to the base system. Sendmail upgraded to version 8.9.3. Tar now supports compressing via bzip2 with the new -y/--bzip2/--bunzip2 flags. TCP Wrappers is now part of the base system. inetd, the port mapper, and sendmail are now linked agaist libwrap. The "PROCESS_OPTIONS" syntax is the default. See `man 5 hosts_options' for more information. Gdb has been updated to version 4.18 and is now part of the standard release for FreeBSD/alpha. Camcontrol now allows users to view the number of tagged openings for any given device, and allows users to set the number of tagged openings for any device that supports tagged queueing. Camcontrol also now allows users to change SCSI negotiation parameters (e.g. sync rate, offset, bus width, disconnection) for devices on certain controllers. Note that this feature is only fully functional for Adaptec 7xxx series controllers, Advansys narrow controllers and NCR/Symbios controllers. Systat, vmstat, and iostat now print out statistics in a more "interesting" order based on "importance" of the device vs. the probe order. And quite a number of bugs, both in the user and kernel, fixed as a result of user feedback for 3.1-RELEASE. 2. Supported Configurations --------------------------- FreeBSD currently runs on a wide variety of ISA, VLB, EISA and PCI bus based PC's, ranging from 386sx to Pentium class machines (though the 386sx is not recommended). Support for generic IDE or ESDI drive configurations, various SCSI controller, network and serial cards is also provided. What follows is a list of all peripherals currently known to work with FreeBSD. Other configurations may also work, we have simply not as yet received confirmation of this. 2.1. Disk Controllers --------------------- WD1003 (any generic MFM/RLL) WD1007 (any generic IDE/ESDI) IDE ATA Adaptec 1535 ISA SCSI controllers Adaptec 154x series ISA SCSI controllers Adaptec 174x series EISA SCSI controller in standard and enhanced mode. Adaptec 274X/284X/2920C/2930U2/294x/2950/3940/3950 (Narrow/Wide/Twin) series EISA/VLB/PCI SCSI controllers. Adaptec AIC7850, AIC7860, AIC7880, AIC789x, on-board SCSI controllers. AdvanSys SCSI controllers (all models). BusLogic MultiMaster controllers: [ Please note that BusLogic/Mylex "Flashpoint" adapters are NOT yet supported ] BusLogic MultiMaster "W" Series Host Adapters: BT-948, BT-958, BT-958D BusLogic MultiMaster "C" Series Host Adapters: BT-946C, BT-956C, BT-956CD, BT-445C, BT-747C, BT-757C, BT-757CD, BT-545C, BT-540CF BusLogic MultiMaster "S" Series Host Adapters: BT-445S, BT-747S, BT-747D, BT-757S, BT-757D, BT-545S, BT-542D, BT-742A, BT-542B BusLogic MultiMaster "A" Series Host Adapters: BT-742A, BT-542B AMI FastDisk controllers that are true BusLogic MultiMaster clones are also supported. DPT SmartCACHE Plus, SmartCACHE III, SmartRAID III, SmartCACHE IV and SmartRAID IV SCSI/RAID controllers are supported. The DPT SmartRAID/CACHE V is not yet supported. SymBios (formerly NCR) 53C810, 53C810a, 53C815, 53C820, 53C825a, 53C860, 53C875, 53C875j, 53C885, 53C895 and 53C896 PCI SCSI controllers: ASUS SC-200 Data Technology DTC3130 (all variants) Diamond FirePort (all) NCR cards (all) Symbios cards (all) Tekram DC390W, 390U and 390F Tyan S1365 QLogic 1020, 1040, 1040B, 1080 and 1240 SCSI Host Adapters. QLogic 2100 Fibre Channel Adapters (private loop only). DTC 3290 EISA SCSI controller in 1542 emulation mode. With all supported SCSI controllers, full support is provided for SCSI-I & SCSI-II peripherals, including hard disks, optical disks, tape drives (including DAT and 8mm Exabyte), medium changers, processor target devices and CDROM drives. WORM devices that support CDROM commands are supported for read-only access by the CDROM driver. WORM/CD-R/CD-RW writing support is provided by cdrecord, which is in the ports tree. The following CD-ROM type systems are supported at this time: (cd) SCSI interface (also includes ProAudio Spectrum and SoundBlaster SCSI) (matcd) Matsushita/Panasonic (Creative SoundBlaster) proprietary interface (562/563 models) (scd) Sony proprietary interface (all models) (wcd) ATAPI IDE interface The following drivers were supported under the old SCSI subsystem, but are NOT YET supported under the new CAM SCSI subsystem: Tekram DC390 and DC390T controllers (maybe other cards based on the AMD 53c974 as well). NCR5380/NCR53400 ("ProAudio Spectrum") SCSI controller. UltraStor 14F, 24F and 34F SCSI controllers. Seagate ST01/02 SCSI controllers. Future Domain 8xx/950 series SCSI controllers. WD7000 SCSI controller. Adaptec 1510 series ISA SCSI controllers (not for bootable devices) Adaptec 152x series ISA SCSI controllers Adaptec AIC-6260 and AIC-6360 based boards, which includes the AHA-152x and SoundBlaster SCSI cards. [ Note: There is work-in-progress to port the AIC-6260/6360 and UltraStor drivers to the new CAM SCSI framework, but no estimates on when or if they will be completed. ] Unmaintained drivers, they might or might not work for your hardware: Floppy tape interface (Colorado/Mountain/Insight) (mcd) Mitsumi proprietary CD-ROM interface (all models) 2.2. Ethernet cards ------------------- Allied-Telesis AT1700 and RE2000 cards Alteon Networks PCI gigabit ethernet NICs based on the Tigon 1 and Tigon 2 chipsets, including the following: Alteon AceNIC (Tigon 1 and 2) 3Com 3c985-SX (Tigon 1 and 2) Netgear GA620 (Tigon 2) Silicon Graphics Gigabit Ethernet DEC/Compaq EtherWORKS 1000 NEC Gigabit Ethernet AMD PCnet/PCI (79c970 & 53c974 or 79c974) SMC Elite 16 WD8013 ethernet interface, and most other WD8003E, WD8003EBT, WD8003W, WD8013W, WD8003S, WD8003SBT and WD8013EBT based clones. SMC Elite Ultra. SMC Etherpower II. RealTek 8129/8139 fast ethernet NICs including the following: Allied Telesyn AT2550 Allied Telesyn AT2500TX Genius GF100TXR (RTL8139) NDC Communications NE100TX-E OvisLink LEF-8129TX OvisLink LEF-8139TX Netronix Inc. EA-1210 NetEther 10/100 KTX-9130TX 10/100 Fast Ethernet Accton "Cheetah" EN1027D (MPX 5030/5038; RealTek 8139 clone?) SMC EZ Card 10/100 PCI 1211-TX Lite-On 82c168/82c169 PNIC fast ethernet NICs including the following: LinkSys EtherFast LNE100TX NetGear FA310-TX Rev. D1 Matrox FastNIC 10/100 Macronix 98713, 98713A, 98715, 98715A and 98725 fast ethernet NICs NDC Communications SFA100A (98713A) CNet Pro120A (98713 or 98713A) CNet Pro120B (98715) SVEC PN102TX (98713) Winbond W89C840F fast ethernet NICs including the following: Trendware TE100-PCIE VIA Technologies VT3043 "Rhine I" and VT86C100A "Rhine II" fast ethernet NICs including the following: Hawking Technologies PN102TX D-Link DFE530TX Texas Instruments ThunderLAN PCI NICs, including the following: Compaq Netelligent 10, 10/100, 10/100 Proliant, 10/100 Dual-Port Compaq Netelligent 10/100 TX Embedded UTP, 10 T PCI UTP/Coax, 10/100 TX UTP Compaq NetFlex 3P, 3P Integrated, 3P w/ BNC Olicom OC-2135/2138, OC-2325, OC-2326 10/100 TX UTP Racore 8165 10/100baseTX Racore 8148 10baseT/100baseTX/100baseFX multi-personality ASIX Electronics AX88140A PCI NICs, including the following: Alfa Inc. GFC2204 CNet Pro110B DEC EtherWORKS III NICs (DE203, DE204, and DE205) DEC EtherWORKS II NICs (DE200, DE201, DE202, and DE422) DEC DC21040, DC21041, or DC21140 based NICs (SMC Etherpower 8432T, DE245, etc) DEC FDDI (DEFPA/DEFEA) NICs Fujitsu MB86960A/MB86965A HP PC Lan+ cards (model numbers: 27247B and 27252A). Intel EtherExpress 16 Intel EtherExpress Pro/10 Intel EtherExpress Pro/100B PCI Fast Ethernet Isolan AT 4141-0 (16 bit) Isolink 4110 (8 bit) Novell NE1000, NE2000, and NE2100 ethernet interface. PCI network cards emulating the NE2000: RealTek 8029, NetVin 5000, Winbond W89C940, Surecom NE-34, VIA VT86C926. 3Com 3C501 cards 3Com 3C503 Etherlink II 3Com 3c505 Etherlink/+ 3Com 3C507 Etherlink 16/TP 3Com 3C509, 3C579, 3C589 (PCMCIA), 3C590/592/595/900/905/905B PCI and EISA (Fast) Etherlink III / (Fast) Etherlink XL 3Com 3c980 Fast Etherlink XL server adapter Toshiba ethernet cards Crystal Semiconductor CS89x0-based NICs, including: IBM Etherjet ISA PCMCIA ethernet cards from IBM and National Semiconductor are also supported. Note that NO token ring cards are supported at this time as we're still waiting for someone to donate a driver for one of them. Any takers? 2.3 ATM ------- o ATM Host Interfaces - FORE Systems, Inc. PCA-200E ATM PCI Adapters - Efficient Networks, Inc. ENI-155p ATM PCI Adapters o ATM Signalling Protocols - The ATM Forum UNI 3.1 signalling protocol - The ATM Forum UNI 3.0 signalling protocol - The ATM Forum ILMI address registration - FORE Systems's proprietary SPANS signalling protocol - Permanent Virtual Channels (PVCs) o IETF "Classical IP and ARP over ATM" model - RFC 1483, "Multiprotocol Encapsulation over ATM Adaptation Layer 5" - RFC 1577, "Classical IP and ARP over ATM" - RFC 1626, "Default IP MTU for use over ATM AAL5" - RFC 1755, "ATM Signaling Support for IP over ATM" - RFC 2225, "Classical IP and ARP over ATM" - RFC 2334, "Server Cache Synchronization Protocol (SCSP)" - Internet Draft draft-ietf-ion-scsp-atmarp-00.txt, "A Distributed ATMARP Service Using SCSP" o ATM Sockets interface 2.4. Misc --------- AST 4 port serial card using shared IRQ. ARNET 8 port serial card using shared IRQ. ARNET (now Digiboard) Sync 570/i high-speed serial. Boca BB1004 4-Port serial card (Modems NOT supported) Boca IOAT66 6-Port serial card (Modems supported) Boca BB1008 8-Port serial card (Modems NOT supported) Boca BB2016 16-Port serial card (Modems supported) Comtrol Rocketport card. Cyclades Cyclom-y Serial Board. STB 4 port card using shared IRQ. SDL Communications Riscom/8 Serial Board. SDL Communications RISCom/N2 and N2pci high-speed sync serial boards. Stallion multiport serial boards: EasyIO, EasyConnection 8/32 & 8/64, ONboard 4/16 and Brumby. Specialix SI/XIO/SX ISA, EISA and PCI serial expansion cards/modules. Adlib, SoundBlaster, SoundBlaster Pro, ProAudioSpectrum, Gravis UltraSound and Roland MPU-401 sound cards. (snd driver) Most ISA audio codecs manufactured by Crystal Semiconductors, OPTi, Creative Labs, Avance, Yamaha and ENSONIQ. (pcm driver) Connectix QuickCam Matrox Meteor Video frame grabber Creative Labs Video Spigot frame grabber Cortex1 frame grabber Hauppauge Wincast/TV boards (PCI) STB TV PCI Intel Smart Video Recorder III Various Frame grabbers based on Brooktree Bt848 and Bt878 chip. HP4020, HP6020, Philips CDD2000/CDD2660 and Plasmon CD-R drives. PS/2 mice Standard PC Joystick X-10 power controllers GPIB and Transputer drivers. Genius and Mustek hand scanners. Xilinx XC6200 based reconfigurable hardware cards compatible with the HOT1 from Virtual Computers (www.vcc.com) Support for Dave Mills experimental Loran-C receiver. FreeBSD currently does NOT support IBM's microchannel (MCA) bus. 3. Obtaining FreeBSD -------------------- You may obtain FreeBSD in a variety of ways: 3.1. FTP/Mail ------------- You can ftp FreeBSD and any or all of its optional packages from `ftp.freebsd.org' - the official FreeBSD release site. For other locations that mirror the FreeBSD software see the file MIRROR.SITES. Please ftp the distribution from the site closest (in networking terms) to you. Additional mirror sites are always welcome! Contact freebsd-admin@FreeBSD.org for more details if you'd like to become an official mirror site. If you do not have access to the Internet and electronic mail is your only recourse, then you may still fetch the files by sending mail to `ftpmail@ftpmail.vix.com' - putting the keyword "help" in your message to get more information on how to fetch files using this mechanism. Please do note, however, that this will end up sending many *tens of megabytes* through the mail and should only be employed as an absolute LAST resort! 3.2. CDROM ---------- FreeBSD 3.2-RELEASE CDs may be ordered on CDROM from: Walnut Creek CDROM 4041 Pike Lane, Suite F Concord CA 94520 1-800-786-9907, +1-925-674-0783, +1-925-674-0821 (FAX) Or via the Internet from orders@cdrom.com or http://www.cdrom.com. Their current catalog can be obtained via ftp from: ftp://ftp.cdrom.com/cdrom/catalog Cost per -RELEASE CD is $39.95 or $24.95 with a FreeBSD subscription. FreeBSD SNAPshot CDs, when available, are $39.95 or $14.95 with a FreeBSD-SNAP subscription (-RELEASE and -SNAP subscriptions are entirely separate). With a subscription, you will automatically receive updates as they are released. Your credit card will be billed when each disk is shipped and you may cancel your subscription at any time without further obligation. Shipping (per order not per disc) is $5 in the US, Canada or Mexico and $9.00 overseas. They accept Visa, Mastercard, Discover, American Express or checks in U.S. Dollars and ship COD within the United States. California residents please add 8.25% sales tax. Should you be dissatisfied for any reason, the CD comes with an unconditional return policy. 4. Upgrading from previous releases of FreeBSD ---------------------------------------------- If you're upgrading from a previous release of FreeBSD, most likely it's 2.2.x or 2.1.x (in some lesser number of cases) and some of the following issues may affect you, depending of course on your chosen method of upgrading. There are two popular ways of upgrading FreeBSD distributions: o Using sources, via /usr/src o Using sysinstall's (binary) upgrade option. In the case of using sources, there are simply two targets you need to be aware of: The standard ``upgrade'' target, which will upgrade a 2.x or 3.0 system to 3.2 and the ``world'' target, which will take an already upgraded system and keep it in sync with whatever changes have happened since the initial upgrade. In the case of using the binary upgrade option, the system will go straight to 3.2/ELF but also populate the //lib/aout directories for backwards compatibility with older binaries. In either case, going to ELF will mean that you'll have somewhat smaller binaries and access to a lot more compiler goodies which have been already been ported to other ELF environments (our older and somewhat crufty a.out format being largely unsupported by most other software projects). Those who wish to retain access to the older a.out dynamic executables should be sure and install the compat22 distribution. Notice that the a.out libraries won't be accessible until the system is rebooted, which may cause trouble with certain a.out packages. Also, do not use install disks or sysinstall from previous versions, as version 3.1 introduced a new bootstrapping procedure, requiring new boot blocks to be installed (because of elf kernels), and version 3.2 has further modifications to the bootstrapping procedure. [ other important upgrading notes should go here] 5. Reporting problems, making suggestions, submitting code. ----------------------------------------------------------- Your suggestions, bug reports and contributions of code are always valued - please do not hesitate to report any problems you may find (preferably with a fix attached, if you can!). The preferred method to submit bug reports from a machine with Internet mail connectivity is to use the send-pr command or use the CGI script at http://www.freebsd.org/send-pr.html. Bug reports will be dutifully filed by our faithful bugfiler program and you can be sure that we'll do our best to respond to all reported bugs as soon as possible. Bugs filed in this way are also visible on our WEB site in the support section and are therefore valuable both as bug reports and as "signposts" for other users concerning potential problems to watch out for. If, for some reason, you are unable to use the send-pr command to submit a bug report, you can try to send it to: freebsd-bugs@FreeBSD.org Note that send-pr itself is a shell script that should be easy to move even onto a totally different system. We much prefer if you could use this interface, since it make it easier to keep track of the problem reports. However, before submitting, please try to make sure whether the problem might have already been fixed since. Otherwise, for any questions or tech support issues, please send mail to: freebsd-questions@FreeBSD.org Additionally, being a volunteer effort, we are always happy to have extra hands willing to help - there are already far more desired enhancements than we'll ever be able to manage by ourselves! To contact us on technical matters, or with offers of help, please send mail to: freebsd-hackers@FreeBSD.org Please note that these mailing lists can experience *significant* amounts of traffic and if you have slow or expensive mail access and are only interested in keeping up with significant FreeBSD events, you may find it preferable to subscribe instead to: freebsd-announce@FreeBSD.org All of the mailing lists can be freely joined by anyone wishing to do so. Send mail to MajorDomo@FreeBSD.org and include the keyword `help' on a line by itself somewhere in the body of the message. This will give you more information on joining the various lists, accessing archives, etc. There are a number of mailing lists targeted at special interest groups not mentioned here, so send mail to majordomo and ask about them! 6. Acknowledgements ------------------- FreeBSD represents the cumulative work of many dozens, if not hundreds, of individuals from around the world who have worked very hard to bring you this release. For a complete list of FreeBSD project staffers, please see: http://www.freebsd.org/handbook/staff.html or, if you've loaded the doc distribution: file:/usr/share/doc/handbook/staff.html Special mention to: The donors listed at http://www.freebsd.org/handbook/donors.html Justin M. Seger for almost single-handedly converting the ports collection to ELF. Doug Rabson and John Birrell for making FreeBSD/alpha happen and to the NetBSD project for substantial indirect aid. Peter Wemm for the new kernel module system (with substantial aid from Doug Rabson). And to the many thousands of FreeBSD users and testers all over the world, without whom this release simply would not have been possible. We sincerely hope you enjoy this release of FreeBSD! The FreeBSD Project